Check beam reaction equilibrium

Use this workflow when a calculation note already lists reactions and you need an independent arithmetic check. The checker does not solve the beam. If you still need the reactions themselves, use the simply supported or cantilever calculator, then come back and test those numbers.

1. Draw the free body and pick the origin

Put the origin at the left end. Upward transverse force is positive. Axial force to the right is positive. A downward service load is therefore negative. Write the span and reject a zero or negative span before any sum.

2. Sum forces and moments about the origin

For plane statics, ΣFx = 0, ΣFy = 0, and ΣM = 0. A point force Fy at station x contributes x·Fy to the moment about the left end. A uniform load contributes its total force at the midpoint. A support reaction contributes its couple plus station times Fy. The residual is load sum plus reaction sum. A useful check is within a stated absolute tolerance, not an unlabeled “close enough”.

3. Solve the example by hand, then compare residuals

Simply supported span L = 8 m. Downward point load P = 24 kN at a = 2 m from the left. Take moments about the left support: RB·8 − 24·2 = 0, so RB = 6 kN upward. Vertical equilibrium: RA + 6 − 24 = 0, so RA = 18 kN upward. Axial reactions are zero. Support couples are zero for a pin and a roller.

Worked numerical example

In newtons, the load is Fy = −24000 N at 2 m. Load moment about the origin = 2 × (−24000) = −48000 N·m. Left reaction Fy = 18000 N at 0 m contributes no moment. Right reaction Fy = 6000 N at 8 m contributes 8 × 6000 = 48000 N·m. Residuals: Fx = 0, Fy = −24000 + 18000 + 6000 = 0, moment = −48000 + 48000 = 0.

If the right reaction is mistyped as 7 kN, Fy residual = 1000 N and the moment residual = −48000 + 8×7000 = 8000 N·m. The check fails. The failure is an arithmetic mismatch, not a statement that a code utilization is high or low.

A full-span uniform load is the same identity. For w = −10 kN/m on a 4 m span, total force = −40 kN at 2 m. End reactions of 20 kN upward cancel both the force and the moment 2×(−40000) + 4×20000.

Limitations

  • The tolerance is one absolute number used for newtons and for newton-metres. A 0.001 tolerance is 0.001 N and 0.001 N·m, which is tight for hand rounding. Widen it only on purpose.
  • Within tolerance means the free body you typed is in equilibrium. It does not check bending stress, deflection, stability, or a design specification.
  • The page will not invent the reaction you left blank. A blank component is invalid. A typed zero is a claim that the component is zero.

References

  • Hibbeler, R. C., Structural Analysis, Pearson. Beam equilibrium and support reactions. Recorded in this site's source registry without an edition or year.
  • Hibbeler, R. C., Engineering Mechanics: Statics, Pearson. Equations of equilibrium for a plane rigid body, ΣFx = 0, ΣFy = 0, ΣM = 0.
  • Meriam, J. L., Kraige, L. G., and Bolton, J. N., Engineering Mechanics: Statics, Wiley. Free-body diagrams and moment summation about a chosen point.

Open the equilibrium checker · Simply Supported Beam Calculator · Reactions, shear, moment, and deflection · Resultant and centroid