CALCULATION PAGES / TITLES, UNITS, ASSUMPTIONS
Reading a structural calculation page
How an engineer reads a structural calculation page on this site: the title names the check, every number keeps its unit, and an elastic result is not a code check.
TITLES A SEARCHER CAN TRUST
The title has to name the check
A structural page is useful in search when the title, the H1, and the description name the same check. This page's H1 is “Reading a structural calculation page”. The document title is that H1 plus the site name. The description under the H1 is the same sentence as the meta description. The canonical URL is https://structuralengineerlab.com/reading-structural-calculations/.
The bending-stress guide follows the same rule. Its title is “Beam Bending Stress: M/S and Mc/I”. Its H1 is “How to Calculate Beam Bending Stress”. Both name elastic bending. Neither says the page applies AISC, Eurocode, ACI, or GB. A title that only said “beam calculator” would not tell a reader whether the page uses M/S, a plastic modulus, or a code interaction formula.
This site publishes one language. The root document is lang="en". There is no second locale, so this page does not emit an hreflang alternate. Directory routes use a trailing slash, and the canonical uses that slash.
UNITS ON THE NUMBER
Convert before you compare two pages
Solvers on this site run in canonical SI. Display fields may accept mm, cm, or m, and centimetre section properties, then convert before the solver. The conversions used by the published tools are 1 cm³ = 10⁻⁶ m³ and 1 cm⁴ = 10⁻⁸ m⁴. Stress results are in pascals; 1 MPa = 10⁶ Pa.
The second-moment trap already stated on the deflection and Euler pages is worth repeating here, because search snippets often drop the power of ten. 8×10⁻⁶ m⁴ is 800 cm⁴. 8 cm⁴ is 8×10⁻⁸ m⁴, one hundred times smaller. Those two inertias are not interchangeable in a deflection or buckling search.
- Second moment
- 1 cm⁴ = 1×10⁻⁸ m⁴. The published deflection and Euler examples use I = 8×10⁻⁶ m⁴ = 800 cm⁴.
- Section modulus
- 1 cm³ = 1×10⁻⁶ m³. The bending-stress load example is S = 200 cm³ = 2×10⁻⁴ m³, with M = 10 kN·m, which is 50 MPa.
- Euler baseline
- E = 200 GPa, I = 8×10⁻⁶ m⁴, L = 3 m, K = 1. Pcr = π²EI/L² = 1754.596 kN. K is typed; it is not inferred from a code column table.
ASSUMPTIONS, INCLUDING CODES
Read the model the page actually uses
- 01Elastic beam: prismatic member, constant E and I, small deflection.
- 02One simple span or a left-fixed cantilever. Point loads and uniform loads.
- 03Section pages report geometry for the named symmetric shapes.
- 04Euler load uses the E, I, L, and K you type. K is not inferred.
- 05No AISC, Eurocode, ACI, or GB allowable is looked up.
Safety classes on the about page match that boundary. S1 is geometry or a ratio you define. S2 is the elastic beam, stress, and Euler analysis. S3, code-based design verification, is prohibited for this catalog. A page that names a textbook source still has to say when the edition or year is unset. The beam bibliography is Hibbeler, Structural Analysis (Pearson), and Roark's Formulas for Stress and Strain (McGraw-Hill), and the source registry does not store an edition or year for those rows.
WORKED EXAMPLE
40 mm by 80 mm rectangle, 8 kN·m
This case is entered by hand. It is not the Load Example stored on the bending-stress page, and it is not the 100 mm by 200 mm rectangle in the section-modulus guide. Width b = 40 mm = 0.040 m. Depth h = 80 mm = 0.080 m. Bending is about the horizontal centroidal axis, so the extreme-fiber distance is c = h/2 = 0.040 m. The rectangle relations used by the section tools are Ix = bh³/12 and Sx = bh²/6.
- Sx
- bh²/6 = (0.040 × 0.080²) / 6 = 2.56×10⁻⁴ / 6 = 4.2666…×10⁻⁵ m³ = 42.666… cm³.
- Ix
- bh³/12 = (0.040 × 0.080³) / 12 = 1.7066…×10⁻⁶ m⁴ = 170.666… cm⁴.
- Stress
- M = 8 kN·m = 8000 N·m. σ = M/Sx = 8000 / (2.56×10⁻⁴ / 6) = 187.5 MPa. Mc/I gives the same 187.5 MPa because Sx = Ix/c.
- Utilization
- If you type demand 187.5 MPa and allowable 200 MPa, the ratio is 187.5/200 = 0.9375. The 200 MPa is the number you typed. It is not a grade looked up by the site, and 0.9375 is not a code pass or fail.
Typing 42.666… cm³ into a field that expects m³, or 170.666… cm⁴ into a field that expects m⁴, changes the stress by orders of magnitude. Use the unit selector on the section-modulus calculator, the moment-of-inertia calculator, and the bending-stress calculator. Those pages convert the unit they display before the solver. The ratio, if you want it, belongs on the user-defined utilization calculator, which rejects a demand and an allowable that are not the same quantity.
For a different published inertia, the Euler calculator baseline remains I = 8×10⁻⁶ m⁴ = 800 cm⁴, not the 170.666… cm⁴ of this rectangle. Column buckling states that ideal elastic Pcr is not a code column check.
PUBLISHED TOOLS AND GUIDES
Open the page that computes the step
Related hubs: beam engineering, beam bending stress, section properties, and structural engineering basics. The four-row topic registry does not include this page. It is an additional published hub, the same way the bending-stress hub sits outside that registry.